FUsion 6 and SATA Equals Blue Screen
The Fusion 6 prompts me that SATA disks are now preferred over SCSI and once the snapshots are cleared there is a GUI for changing bus types. Despite upgrading hardware and then installing tools I get...
View ArticleRe: FUsion 6 and SATA Equals Blue Screen
As an aside I tried converting the XP guest to SCSI which I had not been able to do previously from IDE and that worked OK.
View ArticleRe: FUsion 6 and SATA Equals Blue Screen
Getting better. When I restarted the 7 system with the drive set back to SCSI the SATA controller installed like 30 channels. I then shut down, set the drives to SATA and then was able to restart and...
View ArticleRe: Fusion 6 and unknown PCI Device
To help figure out what is what, the best way to provide comprehensive diagnostic information is to use the "Collect Support Information" command from the VMware Fusion (menu bar)> Help > Collect...
View ArticleRe: FUsion 6 and SATA Equals Blue Screen
gringley wrote: I will assume that for XP the unknown PCI device is the SATA controller and Windows cannot find drivers for it online, and VMware tools are not installing SATA drivers either? Yes the...
View ArticleRe: Install Windows 2003 R2 failed on Esxi 5.1
This is an old topic but anyway I want to put an answer here because I faced exactly the same issue this morning. To get Windows 2003 installed on IBM x3650 M4 just disable "Protected mode" for your...
View ArticleRe: Fusion 6 and unknown PCI Device
If the Virtual Machine's Hard Disk an or CD/DVD have been set to SATA then the unknown PCI device is because Windows XP does not support the VMware Virtual SATA Drive ATA Device. Only certain OSes...
View ArticlePhysical network connectivity to esxi hosts
I need explanation on how to set up the vSwitches with the physical switches both hp procurve's and cisco.connected all nic ports within the hosts to the ports on the cisco switch. I was told to...
View ArticleRe: FUsion 6 and SATA Equals Blue Screen
So the next question is should a Windows XP guest be upgraded to virtual hardware 10? If so then how do I get rid of the unwanted SATA adapter?
View ArticleNew-VApp in a particular folder?
Hi, Is it possible to create a vApp inside a particular folder? For example I have a folder: get-vm 'devdocs' | Get-VMFolderPathUSRCZ1\vm\Build\TeamCity\Dev\ How can I create a new vApp in the "Dev"...
View ArticleClik here to view.
VMware NSX Still Need 3 Physical Server for Controller, just as Nicira did?
Hi All VMware NSX Still Need 3 Physical Server for Controller, just as Nicira did? If so, is there any plan for VM based Controller? When can we get the trail version for NSX? Can't wait to try that...
View ArticleRe: View 5.2 Pool settings for vDGA
Environment isHorizon View 5.2.0 build 987719.ESX 5.1.0 1157734 on Dell R720LG Zero Client 23CAV42K (Tera 2 chip) I have setup GPU passthrough for a VM. I followed recommendations of the following...
View ArticleRe: New-VApp in a particular folder?
Hello, gamename- I do not see where you can specify the folder when creating a new vApp via New-VApp, but you can move the newly created vApp in a subsequent step using the Move-VApp cmdlet. That gets...
View ArticleRe: View 5.2 Pool settings for vDGA
Does not work for me. The second display ALSO maps to the SVGA card and not the K1 card in my case.
View ArticleRe: Boot Camp vm continues to BSoD under Fusion 6
Entegy, >>>It was indeed Hyper-V. However, as Hyper-V being enabled did not affect Fusion 5, I feel this scenario should be looked at. From the VMX configuration file, you uploaded, there is...
View ArticleClik here to view.
Re: Boot Camp vm continues to BSoD under Fusion 6
Thank you for your continued support changhai! However, as I said this computer technically can't even run Hyper-V due to SLAT missing from the processor and it was only enabled by the Windows Phone...
View ArticleRe: Fusion 6 sees 3840x2400 resolution instead of 2880x1800 on MacBook Pro...
The resolution in GOS will be changed accordingly with the VM window size.Enter Full Screen mode, and set "Best for display" in Display settings of Mavericks. Resolution in Win8 should be...
View ArticleRe: New-VApp in a particular folder?
mattboren wrote: Hello, gamename- I do not see where you can specify the folder when creating a new vApp via New-VApp, but you can move the newly created vApp in a subsequent step using the Move-VApp...
View ArticleMoving item from desktop to virtual os
i have vsphere 5 and i am trying to move something from my windows desktop to my rh6 virtual os but it wont let me. I remember that i use to could transfer files this way using workstation. I do think...
View Article